多功能攪拌車大多數的拌和操作均系機械拌和,以中、低壓立式鋼制容器的拌和設備為主,來了解下拌和時機呈現什么問題:
Most of the mixing operations of multi-functional mixer are mechanical mixing, mainly the mixing equipment of medium and low pressure vertical steel containers
緊迫驅動結束后,將驅動軟管卸下,并康復兩車原狀。將多功能攪拌車熄火,將其液壓馬達的高壓油管卸下,并與毛病車上的對應接頭用緊迫驅動軟管相在托輪和滾道之間放入木楔,以操控拌和筒的旋轉。
After the end of the emergency drive, remove the drive hose and recover the two vehicles. Turn off the multi-function mixer, remove the high-pressure oil pipe of its hydraulic motor, and connect it with the corresponding joint on the defective truck with an urgent driving hose. Put a wedge between the supporting wheel and the raceway to control the rotation of the mixing drum.
必定要留意;將發起機熄火,拆松液壓馬達的一根高壓油管,拌和筒可自由旋轉,操控拌和筒的旋轉,使修理孔轉到下部,然后打開修理孔,整理出筒內混凝土,此時必定要留意,混凝土排出結束后,康復拌和車原狀。發起拌和車,將其操作手柄撥出料方位,毛病車內的混凝土即被排出。 準備好緊迫驅動軟管,將拌和車熄火,卸下液壓馬達上的高壓油管接頭。
Be sure to pay attention to safety; turn off the engine, remove a high-pressure oil pipe of the hydraulic motor, and the mixing drum can rotate freely. Control the rotation of the mixing drum to turn the repair hole to the lower part, and then open the repair hole to sort out the concrete in the drum. At this time, be sure to pay attention to safety, and recover the original state of the mixing truck after the concrete is discharged. Start the mixing truck, turn its operating handle to the discharging position, and the concrete in the defective truck will be discharged. Prepare the emergency drive hose, turn off the mixer, and remove the high-pressure oil pipe connector on the hydraulic motor.
多功能攪拌車在上料時有什么要求,假如在進料期間呈現堵料的狀況要怎樣處理,提早如何備料才會(huì )相對來說好些,能盡量防止詳細來看下吧:
What are the requirements of the multi-function mixer when loading? If there is a material blockage during the feeding period, how to deal with it, and how to prepare the material in advance will be relatively better
有時候咱們會(huì )使用手動料槍吸料,為了方便操作直接將料槍刺進物料桶或許噸袋中,料槍吸料口被嚴實的物料壓縮,強大的負壓將滿滿的物料拉走,這對上料機損傷非常大,且極易阻塞管道。
Sometimes we use the manual material gun to suck the material. In order to facilitate the operation, we directly stab the material gun into the material barrel or the ton bag. The suction port of the material gun is compressed by the solid material, and the strong negative pressure pulls the full material away. This is very harmful to the feeder, and it is very easy to block the pipe.
正確的方式是物料在吸料口和空氣構成必定的氣物混合比,在氣流的推進下均勻流入上料機。這個時候咱們需要將料槍規劃帶有補氣功能。假如物料積壓時間過長或許很硬,這個時候需要在料槍上裝一個振蕩器,敲碎結塊的物料。
The correct way is that the material in the suction port and the air constitute a certain air-material mixture ratio, and flow into the feeder evenly under the promotion of air flow. At this time, we need to plan the material gun with air supply function. If the material overstock time is too long, it may be very hard. At this time, we need to install an oscillator on the material gun to break the caked material.